Connecting two Wireless Routers . If the home is not wired for Ethernet and there are several devices which need to be connected to home network then connecting them trough router to router wireless bridge is a good idea. You can opt to use wireless adapters, also known as wireless gaming adapters. You will need one adapter for each device that needs to be connected. This can be expensive option if you have several devices. You can bring network connectivity through wireless to a site and then connect all the devices to the physical Ethernet ports of the router. This is done through wireless bridging. Connecting two wireless routers , requires no cabling in home. Good data speed is required if you want to stream quality digital media from one room to other room using DLNA. In order to setup a wireless bridge, all the routers which you want to connect to the Main Internet Gateway router must have wireless client bridge capability. Steps are very generic , please refer to your routers user manual. Screen shots here are for are for D- Link DIR- 6. You may also ask specific questions about router settings in the comment section below. Log in as admin. Set the router IP address to 1. Enable DHCP server on the router. PRINT Inkjet/SELPHY App. Aplicación Canon PRINT Inkjet/SELPHY PRINT Inkjet/SELPHY App. Fixing computer problems can be frustrating. With DriverGuide, finding helpful support for your driver or firmware problem couldn't be easier! Change the Client IP address range to 1. We Want to reserve 1. IP address. I will explain this in later sections. Set the Wireless security on the router. Make a note of SSID, security key and security type. Avoid using WEP as it works only with 8. Use WPA (with TKIT ) or WPA2(with AES ) for best performance. You will need this for configuring your wireless bridge. Connect router WAN port to your DSL or Cable Modem. Make sure that router has received an IP address and is Capable of connecting to Internet. Windows 7 Drivers for Compaq Presario CQ57-410US: OS: Windows 7 (32-bit) & Windows 7 x64 (64-bit) Driver – Audio (1) Realtek High-Definition (HD) Audio Driver. Conceptronic CH3SNAS Grab. Page 30: Advanced Ftp Server. USB print server port One Power connector. Conceptronic Print Servers CHDDLANU for Windows Vista; Conceptronic Print Servers CHDDLANU for Windows 7; Conceptronic Print. Conceptronic CHDDLANU Print. Test your Internet connectivity using a WIFI enabled laptop ,i. Phone, i. Pod or any WIFI enabled Mobile device. Take your mobile device to sites where you want in Install your Cluster Wireless Bridge. Signal quality should be consistently > 5. Configure Wireless Router as Wireless Bridge to Gateway Router. Assuming that you already have a Router capable of Wireless Bridging. If you haven’t done so click here to go to the page on wireless bridges. Follow instructions below to setup your DD- WRT router. Connect your computer directly into one of the Ethernet (LAN)Ports of the router. Do not connect to the WAN port. Assign your computer an static IP address of 1. Log- in into your router by typing 1. Internet Explorer. Enter your user name and password (default: admin/admin)Go to Wireless/Basic Settings, Select Wireless Mode: Client Bridge,Wireless Network Mode: Mixed,Set Wireless Network name (set on the Gateway Router above),Network Configuration: Bridged. Apply the settings. Go to Wireless/Wireless Security Select the Security Mode of the Gateway Router and Enter the Key you used on the Gateway Router. Apply the settings. Assign a new IP address as 1. Gateway Router. Local IP Address: 1. Subnet Mask: ; 2. Gateway: 1. 92. 1. Local DNS 1. 92. 1. DSL Router IP Address. Disable WAN connection Type. Apply Settings As we have changed the IP address of the Router . Log on using the new IP address. Your Router show now be connected to the Gateway Router. Go to Status Wireless Screen to see the connection quality. Now your Router is configured as a Wireless Bridge and is connected to Internet through Gateway Router. Repeat these steps to configure all your routers you want to setup as bridge. Set up Network Connections for Cluster#1 and Cluster#2. As shown in the above picture connect the wired devices in Cluster#1 and Cluster#2 to the wireless bridge LAN ports. Assign Static IP address to the following machines as we don’t want their IP address to change. Leave all the other machine to get IP address from DHCP server we configured on the Gateway Router. Office Desktop PC – 1. NAS – 1. 92. 1. 68. Media Center HTPC – 1. PS3 – 1. 92. 1. 68. Assign subnet mask of 2. All the devices except above will receive IP address through DHCP server. Test your network using ping or also test Internet connectivity on the HTPC,PC3,Office Computer etc. Now your home networking is complete. To test your network performance go to Measuring Network Performance. Sharing Audio, Video and Pictures.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. Archives
September 2017
Categories |